Mobilux™ EP 0, 1, 2, 3, 004 and 023 products are a high performance family of four general-purpose industrial greases and two special-duty semi-fluid greases. These lithium hydroxystearate greases are formulated to provide extra protection against wear, rusting and water washout. They are available in NLGI grades ranging from 00 to 3, with base oil viscosities ISO VG 150 and 320.
Mobilux EP 0, 1, 2 and 3 greases are recommended for most types of industrial applications including heavy-duty applications where high unit pressures or shock loads are present. These greases provide excellent protection against rust and corrosion and resist water wash-out which makes them particularly suitable for equipment where moist or wet conditions are common. Mobilux EP 0 and 1 are suitable for centralised systems. Mobilux EP 2 and 3 are general-purpose greases. The recommended operating temperature range is from -20ºC to 130ºC but they may be used at higher temperatures if the lubrication frequency is increased accordingly.
Mobilux EP 004 and Mobilux EP 023 are particularly suitable for the lubrication of enclosed gears and bearings in poorly sealed gear cases they can also be used in many other industrial applications where conventional gear oils cannot be retained in gear cases, chain cases, etc. because of leakage due to worn or missing seals. The recommended operating temperature range is -20 to 120ºC for Mobilux EP 004 and -20 to 120ºC for Mobilux EP 023.
Mobilux EP greases have a long history of proven performance and have demonstrated good performance in the areas of corrosion protection, low temperature pumpability and high temperature service life. A Timken OK load of 40 lb illustrates their load carrying and extreme pressure capability.
|Mobilux EP meets or exceeds the requirements of:||Mobilux EP 0||Mobilux EP 1||Mobilux EP 2||Mobilux EP 3||Mobilux EP 004||Mobilux EP 023|
|Mobilux EP has the following builder approvals||Mobilux EP 0||Mobilux EP 1||Mobilux EP 2||Mobilux EP 3||Mobilux EP 004||Mobilux EP 023|
|SEW Eurodrive/ PS C Gears||X|
|Mobilux EP 0||Mobilux EP 1||Mobilux EP 2||Mobilux EP 3||Mobilux EP 004||Mobilux EP 023|
|Penetration, Worked, 25ºC, ASTM D 217||370||325||280||235||415||460|
|Viscosity of Oil, ASTM D 445|
|cSt @ 40ºC||160||160||160||160||160||320|
|Timken OK Load, ASTM D 2509, lb||40||40||40||40||40||40|
|4-Ball Wear, ASTM D 2266, Scar, mm||0.4||0.4||0.4||0.4||0.5||0.4|
|4-Ball Weld Load, ASTM D 2596, Kg||250||250||250||250||250||250|
|Dropping Point, D 2265, C||190||190||190||190|
|Rust Protection, ASTM D 6138, Distilled Water||0-0||0-0||0-0||0-0||0-0||0-0|
Based on available information, this product is not expected to produce adverse effects on health when used for the intended application and the recommendations provided in the Material Safety Data Sheet (MSDS) are followed. MSDS's are available upon request through your sales contract office, or via the Internet. This product should not be used for purposes other than its intended use. If disposing of used product, take care to protect the environment.
The Mobil logotype, the Pegasus design and Mobilux are trademarks of Exxon Mobil Corporation, or one of its subsidiaries.
Copyright © 2001-2016 Exxon Mobil Corporation. All rights reserved.